Gym and fitness club interior design in Seattle: what we design
DeZZign designs fitness clubs, boutique studios for yoga, pilates, cycling and boxing, corporate gyms inside office buildings and private gyms in houses across Seattle, Bellevue and Kirkland. A gym puts more load on a building than most interiors: weights hit the floor, a full class heats the air within minutes, showers run all day and cleaning staff wipe every surface with disinfectant. So we plan the interior together with the structure, the air and the water.
Our portfolio has no standalone commercial gym yet, and we would rather say so than imply one. The projects closest to this work are the following. In Copper Hall (660 m², Kharkiv, 2022), an office building we designed, living plant walls run from the staircase and the main meeting room into a fitness zone with a gym, a small yoga studio and a massage room. Ascetic House (487 m², Kyiv region, 2020 to 2021) was designed for a young owner professionally connected to sport, with a full spa zone and a 25-meter pool for recovery and everyday activity; we took it from the architectural concept through interior design and construction. The Carpathian cottage settlement (10,000 m², designed in 2023, built in 2024) includes a large sports complex with a pool and spa among its buildings.
Gym floor plan: zoning by type of training
We draw the plan from the training program, so the first document we ask for is the list of what members will do and on what equipment. Each type of training sets its own conditions:
- Cardio: rows of treadmills, bikes and rowers, a power point at almost every machine, and a view out, because people face one direction for half an hour.
- Selectorized strength machines: fixed footprints from the supplier's drawings, with space to adjust seats and load pins from the side.
- Free weights and lifting: racks, platforms and dumbbell rows, the heaviest point loads and the loudest impacts in the building.
- Functional training: open floor, a strip for sled pushes, ceiling height for wall balls and ropes, anchors for rigs.
- Group studios: yoga, pilates with reformers, indoor cycling, boxing with heavy bags, each with its own floor, sound and light.
- Recovery: stretching area, massage rooms, sauna and steam room, kept on the quiet and warm side of the plan.
The loud zones go where the structure is strongest and the neighbors least sensitive, usually on a slab on grade or next to the core. Quiet studios move away, with storage or locker rooms as buffers. Reception should see the main floor and the locker room doors, which helps a small late-shift staff.
Circulation follows the member: entrance, check-in, locker room, training floor, back to the shower, out. Nobody coming from the showers should cross the free weight area in socks or flip-flops, and nobody should walk behind a row of running treadmills. Accessibility is part of the same drawing. Under the 2010 ADA Standards, at least one of each type of exercise machine and equipment must have a clear floor space of at least 30 by 48 inches, positioned for transfer or for use from a wheelchair, and those machines must sit on an accessible route. A biceps curl machine and a cable crossover count as two types, as do a treadmill and a rower, but two machines may share one clear space.
Gym flooring for dropped weights: impact noise and vibration
A dropped barbell is the hardest test any interior floor faces, and the problem has two parts. The first is damage: the plate, the topping and the slab underneath need protection. Rubber tiles or rolls do that well, and lifting platforms with a thicker build-up concentrate the worst impacts in one marked area. The second part is the thud that travels through the structure into rooms below and beside the gym. Rubber alone reduces the click and the rattle, but much of the low, heavy sound passes through it.
For a gym on an upper floor or above someone else's business, the usual answer is a floating floor: a heavy layer, often concrete or dense boards, resting on resilient pads or springs that separate it from the building slab. It adds height and weight, so it has to be agreed with the landlord and the structural engineer before the lease is signed. Where a low ceiling cannot take a floating floor plus ducts, we move the lifting area to a lower level or limit what can be dropped and where.
Group classes bring a different structural question. A room full of people jumping to the same beat loads a floor rhythmically, and a floor that is strong enough can still bounce in a way people feel. The structural engineer checks the floor's response to that rhythm, and we place high-impact classes where the structure allows them. Treadmills and heavy machines near a column or a party wall can also carry vibration, so they get isolation pads and some distance from sensitive rooms.
Studio acoustics: cycling next door to yoga
Indoor cycling and HIIT classes run loud music with heavy bass, and yoga or pilates next door needs near silence. Low frequencies pass through light partitions easily, so the separation is built rather than added. Between a cycling studio and a quiet one, we plan heavy, layered walls that run to the structure above the ceiling, solid doors with seals and, for the loudest rooms, a room-within-a-room on its own resilient supports. Ducts crossing the wall get treated too, or one open duct carries the class next door into savasana.
Inside a studio, hard surfaces dominate: mirrors, glass, a sprung or rubber floor. Without absorption, the instructor's voice blurs and the music gets louder to compensate. We add absorbing panels on the walls opposite the mirrors and on the ceiling, out of reach of bars, bands and swinging kettlebells.
Gym ventilation and air exchange
A person running or cycling hard gives off several times the heat and moisture of a person at a desk, and a full class does it all at once. Washington's mechanical code (WAC 51-52, Table 403.3.1.1, in the edition effective March 2024) sets minimum outdoor air for health clubs at 20 cfm per person plus 0.06 cfm per square foot. Its default density is 40 people per 1,000 square feet for an aerobics room and 10 for a weight room. For 30 riders in a 1,000 sq ft cycling studio, the formula gives 600 cfm for the people plus 60 for the area, before any cooling is added.
The same table lists locker and dressing rooms with mechanical exhaust of 0.25 cfm per square foot, and sports locker rooms at 0.5; the mechanical engineer confirms which row the building official applies to your club. Air from those rooms may not be recirculated. In practice, locker rooms and showers are kept at a lower pressure than the gym, so moisture and smells flow toward the exhaust and not onto the training floor.
Two decisions follow for the interior. Supply and exhaust need real space in the ceiling, often more than a former office or shop provides, so we check ceiling heights and duct routes before the layout is fixed. And a studio packed for one hour and empty for the next benefits from carbon dioxide sensors that adjust the airflow to the actual crowd. Seattle's gray, damp months add condensation risk on cold glass and on outer walls of shower rooms, which the engineer and we address with insulation and air movement rather than with a stronger fan alone.
Locker rooms, showers and wet areas
Members judge a club by its locker rooms. We start with peak numbers: how many people arrive for the 6 pm class while the previous one is still showering. That sets the number of lockers, benches, showers, vanities and hair dryer stations, and the floor area between them.
The ADA rules give fixed points. Where locker rooms are provided, at least 5 percent, and no fewer than one, of each type in each cluster must be accessible, with a turning space inside and a bench. That bench is at least 42 inches long and 20 to 24 inches deep, its seat 17 to 19 inches above the floor, with back support or fixed to a wall; in wet locations its surface must be slip resistant and must not hold water. Shelves in those rooms sit 40 to 48 inches above the floor.
For the wet zone itself, we design a continuous waterproofing membrane under the tile, turned up the walls, with floors falling to drains so no puddle stands near a bench. Ask the tile supplier for a slip test made on a wet floor with bare feet, since the test for shoes says little about a shower. Lockers and cubicles should be in materials that tolerate constant humidity, such as compact laminate, with stainless or coated hardware. Closed changing cubicles and shower stalls cost less when planned early than when partitions are retrofitted.
Sauna, steam room and the pool zone
Recovery rooms bring heat and water together. A steam room needs a vapor-tight enclosure, a sloped ceiling so condensation runs down the walls instead of dripping on bathers, and its own drain and ventilation. A sauna needs clearances around the heater set by its manufacturer. Where seating is provided in saunas and steam rooms, the ADA Standards require at least one bench that meets the same bench rules as the locker room, and doors may not swing into its clear floor space.
A pool or spa pool in a club is a public water recreation facility in Washington. Under WAC 246-260-021, the owner obtains a construction permit from the state health department or the local health officer before building or altering it, with plans stamped and signed by an engineer or architect. The general rules in WAC 246-260-031 ask for deck surfaces that slope away from the pool at a minimum of a quarter inch per foot, with a nonslip finish and enough drains to prevent standing water. Pool water treatment, dehumidification of the pool hall and equipment rooms belong to our swimming pool design work, which runs alongside this service when a club has a pool. In Ascetic House the spa and the 25-meter pool sit inside the house program; in the Carpathian settlement the pool and spa are part of the sports complex.
Gym lighting, mirrors and daylight
People in a gym spend a surprising amount of time lying on their backs: on a bench press, on a mat, on a reformer. A bright downlight overhead is a frequent mistake in gym drawings, so we light benches and mat areas indirectly, from coves or wall washers, and keep fixtures off the line of sight of anyone lying down. The main floor gets brighter, even light for safety around weights. Studios get scenes: a cycling class may run in near darkness with accent light, a yoga class wants warm, low light, and both need full light for cleaning.
Mirrors double every fixture they face. We place them after the lighting plan, check reflections from the main training positions and use safety-backed mirror glass at heights where a dumbbell can reach it. Our note on interior lighting explains the layered approach we start from.
Daylight matters a great deal in a city with long, gray winters, and it changes how a basement-like box feels. Copper Hall uses panoramic Schüco windows and generous ceiling heights, and its plant walls continue into the fitness zone; our guide to biophilic design covers how living walls are planned, watered and lit.
Finishes that survive sweat, chalk and disinfectant
Gym surfaces get daily cleaning with strong products, chalk dust, sweat and impacts from equipment. Walls behind racks and dumbbell rows need a protective layer up to the height a plate or bar can swing, for example rubber or plywood behind a durable facing. Corners on delivery routes get guards. Upholstery should be a cleanable contract vinyl or a fabric rated for heavy use, and benches built in the studio need replaceable tops.
In locker rooms and around a pool, chlorine and humidity attack metal and some stones. Porous natural stone stains and needs sealing; porcelain tile handles wet cleaning well. Our material selection work covers samples, schedules and replacement planning, so a damaged tile or locker door can be reordered in a few years rather than redesigned.
Corporate gym, boutique studio or home gym: what changes
A corporate gym in an office building, like the fitness zone in Copper Hall, has to share the building's air, plumbing and floor loads with offices, and it usually has a narrow peak before work, at lunch and after work. Showers matter more than floor size, because people return to their desks. When the gym is one part of a larger workplace, our office design service plans the rest of the floor.
A boutique studio sells one experience, so the entrance, the check-in desk and the studio itself carry the brand, and the locker room has to clear a full class in a few minutes. In a residential building, impact noise toward apartments decides most of the design. A home gym can follow the owner's own training: in Ascetic House, movement and recovery shaped the program of the whole house rather than one room.
Drawings, roles and what moves the cost
The work moves from the program and equipment list to the layout and systems, then the concept with interior renderings, then the drawings: floor and reflected ceiling plans, floor build-ups for each zone, lighting and power with outlets placed per machine, plumbing points, locker room and shower elevations with tile layouts, millwork, finish and furniture schedules. Our article on what is included in an interior design project walks through a full set.
The owner or operator brings the business plan, the class schedule and the final equipment order. The equipment supplier provides footprints, weights and power data. A structural engineer checks floor loads and vibration, a mechanical engineer sizes ventilation, heating and cooling, and a plumbing designer handles drainage and hot water. In Seattle, a change of use always requires a building permit, and SDCI determines the existing use from the last legally permitted business in its records, so a former shop or office becoming a gym starts with that permit history; Bellevue and Kirkland issue their own permits, and we confirm the sequence with each city. Our architects develop the documentation to local codes; drawings that require a local license are signed by licensed professionals we work with.
Cost, timing and supervision for this service are discussed individually. What moves them: the area, whether the space needs a floating floor or a new ventilation system, the number of studios with separate acoustics, whether there are wet areas, a sauna or a pool, the amount of custom millwork, and how many approvals the building needs. Design usually takes four to ten weeks, depending on the size and on how much of the building systems must change.
When this service fits and when another fits better
This service fits when training drives the plan: a new club in a leased space, a boutique studio, a gym inside an office or residential building, or an existing club that needs a new layout, quieter floors or better locker rooms. If the project is mainly treatment rooms and a spa with only a small exercise area, start with beauty salon and spa design. A fitness center that serves hotel guests belongs in hotel and resort interior design, and a club cafe or juice bar that grows into a full kitchen moves to restaurant and cafe interior design. For a pool as the main project, go to swimming pool design.